---
title: "Combimix Betongspackle TDS"
url: https://stacklist.com/card/af2724b2-a2e0-4a82-bd76-492f2f40b6ad
stack: https://stacklist.com/c/business/stack/6ef6e379-b702-4156-8fa8-00346fb192a1
summary: "Combimix Concrete Resurfacer is a wear surface product for concrete renovation that provides high bondage to substrates and is frost-resistant, applicable from feather edge up to ½ inch on various surfaces. The product requires specific temperature conditions (50-80°F), mixing ratios, and post-treatment procedures including post-watering for optimal strength development."
tags: "concrete-resurfacer, construction-material, product-datasheet, concrete-repair, surface-coating, frost-resistant, technical-specifications"
key_entities: "Combimix (organization), Combimix AB (organization), Bålsta (location), Sweden (location), Concrete Resurfacer (technology), frost-resistance (concept), compressive-strength (concept)"
classification: "reference"
content_hash: "sha256:4e24a8b1b8c62e3c83d5772884182b55775cb1b73f3ad63d2ff525f465c696bd"
acp_version: "0.2"
token_counts_approximate: 1010
visibility: public
agent_accessible: true
status: "final"
---

# Combimix Betongspackle TDS

v 
Combimix datasheet 
Combimix Concrete Resurfacer Product category: Concrete 
Date: 2019-01-02 
Page: 1(1) 
0.74-0.95q 10 lb 3–4 
min 
45–60 
min 
50 – 80 ° F 0– 1/2" 
ca 60
min 
72 
hrs 
General Use 
Provides a wear surface for concrete renovation. It can serve as a thin, full-coverage wear
surface. Offers high bondage to the substrate and is frost-resistant. Can be applied from a
feather edge up to ½ inch. The material can be overpainted. 
Area of use 
Concrete Filler is used for smoothing and for repairs of smaller holes in a concrete base. The filler
is used for example, on stairs, garage floors, natural stone and mineral substrates. The product
can be used both indoors and outdoors, as well as on horizontal and vertical surfaces. 
Pre-treatment 
For best result, the temperature in the work area should be between 50 – 80 ° F . Store the
dry mortar and other materials so that they will remain over 10 °C before use. At temperatures
lower than 40 ° F , the strength development will cease. If the product is used in
temperatures below 40 ° F , then winter measures should be implemented. The substrate
should be clean and free from dust, cement skin, grease or other impurities that can prevent
adhesion. Smooth or glossy surfaces may need to be primed for maximum adhesion. Dry
and highly-absorbent substrates may be pre-watered. 
Mixing 
Add 10 lb of Combimix Concrete Resurfacer with a maximum of 0.85 quarts of cool,
potable water. Mix for 2 minutes with a heavy-duty drill mixer until a homogeneous
mass is achieved. Let the product sit for 30 seconds and then remix for an
additional 30 seconds. 
Application 
Apply with a trowel, a brush or broom, thoroughly working the product into the substrate.
The surface can be filled or brushed. Edge cut repairs after approximately 1 hour. Discard
any filler that has begun to cure if it cannot be mixed with water. 
Working Time 
30 minutes at 70°F. 
Post-treatment and curing 
Protect newly-cast surfaces from direct sunshine, rain and high wind. The strength will increase
with post-watering of the cured material. Post-watering may be done for at least three days
in dry and warm weather, as well as in the case of strong winds. Use a water hose with a
fine spray nozzle. Then cover the post-watered surface with plastic. 
Storage time and packaging 
Store in a dry environment. The storage life is 12 months from the date of production in the
unopened original packaging. The date of production is printed on the packaging.
The product is delivered in bags of 10 lb . 
Residual products and safety information 
Empty bags can be burned. Any remaining, dry powder that has been stored properly can
be used again. Hardened material should be disposed of as construction waste. Do not
wash the product into the sewage system. The cement in the product has a reduced level
of chromate. Follow regulations in each respective country. 
Health, environment, safety and technical service documents 
For current version of product information, contact Combimix at
info@combimix.se. Previously undated and dated issues are no longer valid. For more
information contact our sales organization. 
Technical data 
Grain size 1/64" 
Compressive strength class 4350 psi 
Water demand 0.74-0.95 q /10 lb 
Water cement ratio 0,4 
Air content 4–6 % 
Workable 20 °C 45–60 min 
Begins to dry after approx. 60 min 
Application depth 0– 1/2" , 
in holes up to 2" 
Frost resistance Good 
Material consumption approx. 45 sqft @ 1/16" 
Color Grey 
This product sheet contains general information. Products can be
used in a number of changing conditions and situations. Combimix
is not responsible for the storage, use in construction, processing or
design, interactions with other products, required use due to local
conditions or other external factors. Combimix is also not responsible
for cases where the above information has been misinterpreted or
neglected by the user. 
Combimix AB • Verkstadsvägen 6 • 746 40 Bålsta • Tel. +46 (0)171-46 65 90 • info@combimix.se 
Binder Portland cement